Protease Inhibitor Cocktail
Cat. No.
G135
Unit
1.0 ml
Price
$173.00
Specifications
| Cat. No. | G135 |
| Name | Protease Inhibitor Cocktail |
| Price | $173.00 |
| Unit | 1.0 ml |
| Category | Reagents and Chemicals |
| Description |
Protease Inhibitor Cocktail is used to prevent the digestion of proteins that occurs after cell lysis takes place. |
| Recommended Protocol |
1mL of the Protesase Inhibitor Cocktail is recommended for the inhibition of protease activity form 100mL of cell lysate at a density of 10^8 cells per mL.
However, since not all organisms contain the same level of endogenous proteases, it is up to the researcher to optimize the concentration for their experiments. |
| Storage Condition |
Store at -20°C. The product is stable for a year upon receiving when properly stored. If there are crystals observed in the solution, place the product at room temperature for 5 minutes before use. |
Documents
FAQs
| I would like to know under what circumstance I could have no signal? | |
|
Here are some suggestions and how you could resolve the problem:
1. The primary antibody and the secondary antibody are not compatible.
Use secondary antibody that was raised against the species in which the primary was raised (e.g primary is raised in rabbit, use anti-rabbit secondary).
2. Not enough primary or secondary antibody is bound to the protein of interest.
Use more concentrated antibody. Incubate longer (e.g. overnight) at 4ºC.
3. Cross-reaction between blocking agent and primary or secondary antibody.
Use a mild detergent such as Tween20 or switch blocking reagent (i.e. commonly used blocking reagentsare milk, BSA, serum or gelatin).
4. The primary antibody does not recognize the protein in the species being tested.
Check the datasheet or perform a ClustalW alignment to ensure your antibody should react with the target protein; Run the recommended positive control.
5. Insufficient antigen.
Load at least 20-30 ug protein per lane; Use protease inhibitors; Run the recommended positive control.
6. The protein of interest is not abundantly present in the tissue.
Use an enrichment step to maximize the signal (e.g. prepare nuclear lysates for a nuclear protein, etc.).
7. Poor transfer of protein to membrane.
Check the transfer with a reversible stain such as Ponceau S; check that the transfer was not performed the wrong way; if using PVDF membrane make sure you pre-soak the membrane in MeOH then in transfer buffer.
8. Excessive washing of the membrane.
Do not over wash the membrane.
9. Too much blocking does not allow you to visualize your protein of interest.
Instead of using 5% milk in the antibody buffers try removing the milk or using 0.5%; Switch blocking reagents or block for less time.
10. Over-use of the primary antibody.
Use fresh antibody as the effective concentration is lowered upon each re-use.
11. Secondary antibody inhibited by sodium azide.
Do not use sodium azide together with HRP-conjugated antibodies.
12. Detection kit is old and substrate is inactive.
Use fresh substrate.
|
References
- Kim, BY et al. "Corneal Dystrophy-associated R124H Mutation Disrupts TGFBI Interaction with Periostin and Causes Mislocalization to the Lysosome" J Biol Chem 284 (29):19580-19591 (2009). DOI: 10.1074/jbc.M109.013607. Application: Protein Isolation Assays.
- Kim, S., Lee, M. S., Jung, S., Son, H. Y., Park, S., Kang, B., ... & Kim, Y. "Ginger Extract Ameliorates Obesity and Inflammation via Regulating MicroRNA-21/132 Expression and AMPK Activation in White Adipose Tissue" Nutrients 10(11):1567 (2018).
- Tang, X., McMullen, T. P., & Brindley, D. N. "Increasing the low lipid phosphate phosphatase 1 activity in breast cancer cells decreases transcription by AP-1 and expressions of matrix metalloproteinases and cyclin D1/D3" Theranostics 9(21):6129 (2019).
Controls and Related Product: